How to Work Safely Under a Car
Learn how to raise a car safely, place jack stands and wheel chocks, and set up a stable workspace before any job under the vehicle.
Contents
- Why a jack alone is not enough
- Choose level, solid ground first
- Set the parking brake and chock the wheels
- Find the correct lift points
- Place jack stands under structural points
- Add a backup under the vehicle
- Work with care once you are underneath
- Questions about working under a car
- How do I safely jack up a car to work under it?
- Can I work under a car supported only by a jack?
- Where do jack stands go under a car?
- Do I need wheel chocks when the car is on jack stands?
- What should I put under a car as a backup?
- Is it safe to run the engine under a raised car?
Working safely under a car means the vehicle rests on rigid supports, not on a jack alone. You raise the car at the correct lift point, set jack stands under strong structural points, and chock the wheels that stay on the ground. A few minutes of setup protects you from a falling vehicle.
- Never work under a car supported only by a jack, because a hydraulic jack can lose pressure.
- Set jack stands under structural points such as the subframe or axle, not under sheet metal or plastic.
- Chock the wheels still on the ground so the car cannot roll while it is raised.
- Work on level, solid ground, and place a wheel or a spare under the car as a backup.
- Record each job and the parts used in a service log so future maintenance stays organized.
Why a jack alone is not enough
A hydraulic jack is a lifting tool, not a support tool. Its seal can fail or its valve can creep down while you are underneath. Lifting safety depends on a second, rigid support that holds the car at a fixed height.
Never work under a car supported only by a jack. Even a jack that feels firm can drop when the load shifts or the fluid warms. Jack stands are designed to carry a steady load and stay put.
Treat the jack as a way to get the car up, then transfer the weight to stands before you go under it. Keep the jack in place as a second contact point if you like, but do not rely on it.
Choose level, solid ground first
Under-car safety starts with where the car sits. A level, hard surface such as concrete or firm asphalt keeps the jack and stands from sinking or sliding. Gravel, grass and soft soil let a stand tilt and dig in.
Check the ground for slope, cracks and loose material before you lift anything. Move the car to a flat spot if the current place is uneven. A small tilt grows into a large problem once the car is in the air.
Clear the area around each wheel so you have room to place the jack and the stands. Remove tools and cords from the path where the car will rise. A clean floor also lets you see leaks and damage later.
Set the parking brake and chock the wheels
Wheel chocks stop the car from rolling while it is raised. Set the parking brake and put the transmission in park or in gear before you lift. Chock the wheels that will stay on the ground.
Place a chock at the front and back of at least one ground wheel, on the side opposite the lift. For a front lift, chock the rear wheels; for a rear lift, chock the front wheels. A solid block of wood or a purpose-made chock works.
Chocking matters most when you lift one end of the car. The raised end has less grip, and any push can slide the whole vehicle. Chocks hold the grounded wheels so the car stays where you put it.
Find the correct lift points
Every car has specific lift points designed to carry its weight without damage. Your owner's manual or a service manual shows where they are on your model. Using the wrong spot can bend the floor pan or crush a fuel or brake line.
Lift points sit on structural parts such as the subframe, the axle or a reinforced seam near the wheels. Avoid the middle of a door sill, plastic covers, the oil pan and the exhaust. Those parts bend, crack or crush under load.
Place the jack saddle flat against the lift point and check the contact before you pump. A saddle that touches only an edge can slip as the car rises. Raise the car slowly and watch the jack and the contact point.
Place jack stands under structural points
Jack stands carry the car once it is raised, so they need a strong, flat place to sit. Put each stand under a structural point such as the subframe, the axle or a reinforced jack point. The stand's saddle should meet the car squarely.
Set the stand height before you slide it under, and lock the pin or ratchet in place. Raise the stand so its saddle meets the car with little gap, then lower the jack slowly onto the stands. Check that each stand sits flat and upright.
Use stands rated for the load and place one at each lifted corner. Give the car a firm, gentle push sideways before you go under. Any wobble or shift means you reset the stands, not that you proceed.
- Read the owner's manual for the lift points on your model.
- Park on level, hard ground and set the parking brake.
- Chock the wheels that remain on the ground.
- Raise the car at a structural lift point with the jack.
- Place a jack stand under each lifted corner.
- Lower the car onto the stands and check they are flat.
- Push the car gently to confirm it is stable.
- Keep a wheel or spare under the car as a backup.
Add a backup under the vehicle
A second layer of protection costs little and adds a physical stop if a stand fails. Slide a wheel, a spare tire or a sturdy block under a structural part of the car. Leave a small gap so the car does not rest on the backup yet.
The backup should sit under a strong point, not under a flexible panel. A wheel laid flat under the subframe gives the car something to land on. This step does not replace jack stands but adds a margin if one shifts.
Keep the backup in place for the whole job and remove it only after the car is back on the ground. Check its position whenever you move around under the car. A backup that has shifted offers no protection.
Work with care once you are underneath
Once the car is supported, keep your movements slow and deliberate. Avoid jerking tools or pushing hard against the car, since force can shift it on the stands. Keep your body out from directly under heavy parts such as the engine and transmission.
Keep the work area clear so you can move out quickly if something feels wrong. Do not run the engine while you are under a raised car unless the job truly requires it. Exhaust, moving belts and hot parts add risk in a cramped space.
Some jobs need a trained specialist, including work on fuel systems, high-voltage batteries and structural repairs. Stop and get professional help when a task goes beyond your tools or knowledge. Record the job, the date and the parts used in a service log so the next task starts with clear notes.
Questions about working under a car
How do I safely jack up a car to work under it?
Jack up a car safely by parking on level, hard ground, setting the parking brake and chocking the ground wheels. Raise the car at a structural lift point with a jack, then place jack stands under strong points before you go underneath. Lower the car onto the stands and check that each one sits flat.
Can I work under a car supported only by a jack?
No, you should never work under a car supported only by a jack. A hydraulic jack can lose pressure or slip, and it is a lifting tool rather than a support. Jack stands carry the weight and hold the car at a fixed height.
Where do jack stands go under a car?
Jack stands go under structural points such as the subframe, the axle or a reinforced jack point. Avoid sheet metal, plastic covers, the oil pan and the exhaust, because those parts bend or crush. Your owner's manual shows the lift points for your model.
Do I need wheel chocks when the car is on jack stands?
Yes, wheel chocks add stability whenever the car is raised. They hold the wheels still on the ground so the vehicle cannot roll or slide. Place chocks at the front and back of a wheel that stays down.
What should I put under a car as a backup?
A wheel, a spare tire or a sturdy block placed under a structural part works as a backup. Leave a small gap so the car does not rest on it during normal work. The backup adds a physical stop if a stand shifts or fails.
Is it safe to run the engine under a raised car?
Running the engine under a raised car adds risk from exhaust, moving parts and heat. Do it only when the job requires the engine running, and keep clear of belts and hot surfaces. Many under-car jobs are safer with the engine off.