Tire Tread Depth Measurement Chart
Learn how to read a tire tread depth measurement chart, compare inch and millimeter readings, and see where new and worn tires fall on the gauge table.
Contents
- Reading the gauge against the table
- Inches and millimeters on one chart
- Using the penny test as a reference
- Tire Tread Depth Chart Questions
- What does a tire tread depth gauge chart show?
- How do I read a tire tread depth measurement chart in millimeters?
- What is the difference between a new tire at 10/32 inch and a worn tire at 2/32 inch?
- Can the penny test replace a tread depth gauge chart?
A tire tread depth measurement chart converts the reading on a tread depth gauge into a wear level, so you can judge how much rubber remains on the tire. The chart lists readings in fractions of an inch or in millimeters and marks the points where a tire counts as new, worn or due for replacement. Keeping each reading with the service date in your vehicle record shows how fast the tread is wearing between checks.
Reading the gauge against the table
A tread depth gauge gives one number for the groove you probe, and the chart tells you what that number means for the tire. Push the gauge probe into a main circumferential groove and read the scale in the unit the chart uses. Repeat the measurement at several points around the tire and across the tread width. Write each gauge reading next to the service date so the chart comparison stays meaningful over time.
Inches and millimeters on one chart
Tire tread depth charts present the same wear in two units, and the conversion between them is fixed. A new tire reading of 10/32 inch equals about 7.9 millimeters, while a worn tire at 2/32 inch equals about 1.6 millimeters. The 2/32 inch level is the wear indicator where a tire is considered worn out for wet grip. Charts printed in millimeters show the matching values so a metric gauge reads the same as an inch gauge.
Using the penny test as a reference
The penny test is a reference check that needs no gauge, and the chart explains where its result sits. Insert a penny upside down into a groove with Lincoln's head pointing down. If the top of Lincoln's head is fully visible, the tread is at or near the 2/32 inch mark on the chart. A penny test confirms a low reading, but a gauge gives the precise number to record.
Tire Tread Depth Chart Questions
What does a tire tread depth gauge chart show?
A tire tread depth gauge chart shows how a measured reading maps to a wear level on the tire. The chart pairs inch fractions with millimeter values and marks the new, worn and replacement points. You compare your gauge reading to the table to decide the next step. Recording the reading with the date turns the chart into a wear history.
How do I read a tire tread depth measurement chart in millimeters?
A tire tread depth measurement chart in millimeters lists the same wear levels as the inch version, converted to metric units. Read the gauge in millimeters and find the matching row on the table. The 2/32 inch wear point appears as about 1.6 millimeters on the metric side. A new tire at 10/32 inch shows about 7.9 millimeters on the same chart.
What is the difference between a new tire at 10/32 inch and a worn tire at 2/32 inch?
A new tire at 10/32 inch carries full tread, while a worn tire at 2/32 inch sits at the wear indicator on the chart. The difference between the two readings is the tread lost over the tire's life. A gauge reading near 2/32 inch means the tire is due for replacement. Chart both numbers in your record so the drop between services is visible.
Can the penny test replace a tread depth gauge chart?
No, the penny test cannot replace a tread depth gauge chart because it gives a pass or fail reference rather than a number. The penny test shows whether tread has reached about 2/32 inch. A gauge provides the exact reading you plot on the chart. Use the penny test as a quick reference and the gauge plus chart for the recorded measurement.
Read next
-
How Tire Rotation Patterns Work and Why Recording Them Matters
-
Tire Rotation in Logan, Utah: Tracking Wear History and Service Costs
-
How to Find and Read Tire Date Codes to Determine Tire Age
-
Keep a Tire Rotation Log: Track Rotation History, Odometer Readings, and Service Costs
-
Keep a Tire Tread Depth Record: Your Essential Guide
-
When to Replace Car Tires: Mileage, Intervals and Wear