RECORDS / TERMS / THE NEXT APPOINTMENT

Torque Wrench Settings Chart

Learn how to read a torque wrench settings chart, convert ft-lb and N·m values, and set your wrench to the right torque specification for each fastener.

8 min read0 views
— · 0 votes
Contents
  1. What a torque wrench settings chart does
  2. How to read torque wrench settings
  3. Metric torque wrench settings chart
  4. Setting the wrench to the right value
  5. Torque wrench settings conversion chart
  6. Click-type and beam torque wrenches
  7. Recording torque values with your service notes
  8. Torque Wrench Settings Questions
  9. How do I read torque wrench settings on the handle?
  10. What should I set my torque wrench to?
  11. Where can I find a torque wrench settings chart PDF?
  12. How does a torque wrench settings conversion chart work?
  13. Does a metric torque wrench settings chart use different numbers?
  14. Can I reuse a torque value from a similar fastener?

A torque wrench settings chart pairs each fastener with a torque specification, given in ft-lb or N·m, and shows you where to set the wrench. Read the value for the exact fastener, convert units if your wrench and chart differ, and dial the wrench to that figure. The chart is only as good as the specification it comes from, so match the fastener, thread and application before you trust a number.

  • Find the fastener's torque specification first, then set the wrench to that value.
  • Match the unit on the wrench to the unit on the chart before you dial anything.
  • Convert ft-lb to N·m by multiplying by a fixed factor of about 1.356.
  • A click-type wrench signals at the set value, while a beam wrench shows torque as you pull.
  • Record each torque value and date in your service notes so the next job starts faster.

What a torque wrench settings chart does

A torque wrench settings chart is a reference that lists fasteners next to the torque value each one needs. The value is the torque specification set by the vehicle or component maker for that joint, thread and material. The chart translates that specification into a setting you can dial on the wrench.

The chart does not create torque values on its own. Every number on a good chart traces back to a published torque specification for a specific fastener. Use the chart for the fastener in front of you, not for a similar bolt nearby.

A settings chart also keeps your work consistent across jobs. When the same fastener appears again, you set the wrench from the same reference and get the same result. Write the value you used in your service record so the next service starts from a known figure.

How to read torque wrench settings

Reading torque wrench settings starts with the scale on the wrench body or handle. A click-type wrench has a numbered scale and a smaller vernier scale that together show the set value. A beam torque wrench has a pointer and a scale you read while pulling.

Locate the unit printed on the scale, such as ft-lb or N·m, before you read the number. Follow the main scale to the nearest mark, then use the vernier or micrometer marks for the finer portion. Lock the handle once the setting matches the chart.

Turn the handle slowly and check the scale again after locking. Some wrenches shift slightly as the lock engages, so re-read the setting. Confirm the number against the chart one more time before you apply torque to the fastener.

  • Identify the unit on the wrench scale first.
  • Read the main scale to the nearest graduation.
  • Use the vernier marks for the fractional part.
  • Lock the handle and re-check the setting.
  • Compare the final number with the chart.

Metric torque wrench settings chart

A metric torque wrench settings chart lists values in newton-meters, written N·m, for fasteners specified in metric units. Metric fasteners are sized by thread diameter and pitch, and the specification follows that sizing. Keep the metric chart separate from an inch chart so you do not mix the two.

Many metric specifications fall in a range rather than a single figure, such as a minimum and maximum value. Set the wrench within that range and stay consistent across identical fasteners. If the wrench scale is marked in ft-lb only, convert the N·m figure before setting.

Check the thread pitch as well as the diameter when you read a metric chart. Two bolts with the same diameter but different pitch can carry different torque specifications. Match both numbers to the fastener before you apply the setting.

Setting the wrench to the right value

What you set your torque wrench to should come from the specification for that exact fastener, not from habit. Look up the fastener in the chart, note the unit, and set the wrench to that figure. If the chart gives a range, pick a value inside it and record which one you used.

Set the wrench before the fastener is snug, then apply torque in a smooth pull until the wrench signals. A click-type wrench clicks or releases at the set value, and a beam wrench pointer lines up with the scale. Stop at the signal and do not add extra pull.

Tighten fasteners in the sequence the maker specifies when a joint has several of them. Re-check the setting on the wrench after each fastener if the handle can move. Record the value and the date so the record matches what the vehicle actually received.

Torque wrench settings conversion chart

A torque wrench settings conversion chart changes a value from one unit to another, such as ft-lb to N·m. The conversion uses a fixed factor, so the same input always gives the same output. Convert first, then set the wrench to the converted figure.

One foot-pound equals about 1.356 newton-meters, and one newton-meter equals about 0.738 foot-pounds. Multiply or divide by the factor that matches the direction you need. Round the result to a value your wrench scale can actually show.

Keep the original specification visible next to the converted number in your notes. A rounded conversion is close but not identical to the source figure. The original value remains the reference if a question comes up later.

FromToMultiply by
ft-lbN·m1.356
N·mft-lb0.738
in-lbft-lb0.083
ft-lbin-lb12

Click-type and beam torque wrenches

A click-type wrench holds a set value and signals with a click or release when you reach it. The setting is dialed on the handle, so the chart value goes straight onto the scale. This design suits work where you cannot watch a pointer while pulling.

A beam torque wrench bends a beam against a pointer and shows torque on a scale as you pull. You read the value at the moment the pointer reaches the target. This design shows the whole pull, which helps when you want to see how torque builds.

Both designs need the chart value translated to their own scale. A click wrench needs the value dialed in, and a beam wrench needs the value read as a target on the scale. Handle each tool according to its maker's instructions, and have a trained specialist service it when it drifts.

Recording torque values with your service notes

Recording each torque value turns a settings chart into part of your vehicle history. Note the fastener, the value, the unit and the date in the same place as your other service details. The record then shows what the vehicle received and when.

A written value also saves time on the next service. Instead of searching the chart again, you check the last entry and confirm it against the current specification. Keep the chart reference next to the value so the source stays traceable.

Bring the torque record together with dates and everyday vehicle costs in one organized file. A record that starts with the details you already have grows into a useful history. The chart answers the setting question, and the record answers what was done.

Torque Wrench Settings Questions

How do I read torque wrench settings on the handle?

You read torque wrench settings by finding the unit on the scale, then following the main marks to the nearest value. Use the smaller vernier marks for the fractional part of the setting. Lock the handle and re-read the number before you apply torque.

What should I set my torque wrench to?

Set your torque wrench to the torque specification for the exact fastener, thread and application you are tightening. Take the figure from the maker's specification or a chart built from it, and match the unit on the wrench. If the specification is a range, choose a value inside it and record it.

Where can I find a torque wrench settings chart PDF?

A torque wrench settings chart PDF is a printable version of the same reference, and the source matters more than the file type. Use a PDF that names the vehicle or component and the fastener it covers. Check that the values match your specification before you rely on the file.

How does a torque wrench settings conversion chart work?

A torque wrench settings conversion chart changes a value between units, such as ft-lb and N·m, using a fixed factor. One foot-pound equals about 1.356 newton-meters, so you multiply or divide by the factor for the direction you need. Round the result to a value the wrench scale can show.

Does a metric torque wrench settings chart use different numbers?

A metric torque wrench settings chart lists values in newton-meters, written N·m, for metric fasteners. The numbers differ from an inch chart because the units differ, even when the fastener is the same size. Convert the value if your wrench scale is marked in ft-lb.

Can I reuse a torque value from a similar fastener?

No, a torque value from a similar fastener is not a substitute for the specification of the joint you are tightening. Thread pitch, material and the joint design can change the correct figure. Use the published specification for that fastener and record the value you applied.

Read next

Latest articles